Slide Out Parts

RV Designer Wiring Harness for DC Contour Switch, 40AHarness used with contoured switch 55-0802 (S141) or 55-0803 (S145). Harness is 6" long with a 5-pin square connector. Note: Picture shows contour switch. Item is for the wiring harness only.

20A continuous, 40A peak For motor switching/reversing applicationsFeatures a 5-pin square connectorCut-out size: 1.85" x 2.3"Mounting plate text: “Slide Room”Typical Applications: SlideoutsMotor control

20A continuous, 40A peak For motor switching/reversing applicationsFeatures a 5-pin square connectorCut-out size: 1.85" x 2.3"Mounting plate text: “Slide Room”Typical Applications: SlideoutsMotor control

RV Designer Wiring Harness for DC Rocker Switch Harness for rocker switch 55-0800 (S125). Harness is 6" long with a 5-pin connector.

20A continuous, 40A peak For motor switching/reversing applicationsFeatures an in-line 5-pin connectorCut-out size: 1.52" x 0.73"Mounting plate text: “Slide Room”Typical Applications: SlideoutsPower seatsSofasDoor locksWindows

Camco RV Slideout Lube And Protectant, 16 oz Lubricant makes sure your slide-out operates smoothly without sticking. Leaves a dry film that repels dirt and grime plus protects against rust and corrosion. Priced each.

Produces a bead of foam that stays where you spray. No runs, drips or mess! Use on fiberglass, aluminum and vinyl.

Camco RV Slideout Rubber Seal Conditioner, 16 oz Protects and conditions the seals on your slideouts. Shields against UV rays and decreases friction, making seals last longer. Priced each.

Suggested Applications: Lubricates door locks, trunk lids, brake cable, rubber molding, etc. Lubricates metal and rubber Prevents sticking, freezing and squeaking Withstands -40° F to +400° F Protects plastic, wood, metal and...

AmeriTrim RV Rubber Seal, 5/8" x 3/8", 30'Seals your RV's cabinets, doors, windows and more. Rubber seals come in a variety of specially designed shapes for a variety of applications. Easy to apply. Cut the desired size needed, peel back the cover strip,...

AmeriTrim RV Rubber Seal, 3/8" x 3/16", 50'Seals your RV's cabinets, doors, windows and more. Rubber seals come in a variety of specially designed shapes for a variety of applications. Easy to apply. Cut the desired size needed, peel back the cover...

 Industrial grade rust inhibitor protects and resists dirt, sand, salt, and road grime for extended periods of time plus displaces moisture longer.

Protects mechanism from road elements Displaces moisture to prevent rust CFC-Free

Prevents fading, cracking and deterioration Long-lasting UV protection Non-petroleum formula that’s tested safe (petroleum-based formulas can cause swelling, cracking or degradation of rubber seals) Protective coating repels...

Black - 24" Stroke1.5" Bore39" Retracted63" Extended

18:1 Kit containts the following: (1) EA A-8504-01 18:1 2nd Reduction Gear (1) EA 8579-11 18:1 Clutch Assembly (1) EA 5/16" Pin

Bi-Directional 12V DC 0.8 KW 1.4 GPM at 0 PSI Fixed Clearance Pump Orientation: Horizontal Tank: 2 QT

Protects slide-out plumbing, wiring and hoses during extension and retraction of slide roomCan be installed on any slide-out system that uses a 1/4-inch steel rod or swing arm for the same applicationSingle, double and triple applicationsAll kits come...

18:1 Ratio 12 VDC 30 AMP

18:1 Gear Ratio 12 VDC Speed: 9,000 RPM

Standard Crank Handle for Lippert Landing Gear and Manual Slide-Outs

The "New" style switch configuration wasinstalled in Lippert slide-out mechanisms after May of 2006.

12" Diametric Pitch; 14.5 Degree Pressure Angle

These plastic wear pads are standard on all Lippertinboard and outboard electric and hydraulic slide-outs, manualslide-outs, and motorized RV slide-outs as well as the electricstabilizer jack.

40" Venture Actuator Only

12VDC 12 RPM HP: 1/10 9 AMPS

Lippert 28:1 Venture Actuator & Motor

40" Venture Actuator w/ 18:1 Hi Speed Motor

Motor Specifications: HP: 1/15Amps: 7.5RPM: 10VDC: 12

Fits 2.5" x 2.5" square slide-out tubing. Gear has 15 teeth.

Lippert Gear Pack 2x3 Slideout

Slideout Controller 2.070 x 1.5

Replaces the motor for your tandem landing gearDesigned for use with Stromberg Carlson LG-1 landing gearMeasures 3-3/4" long x 4-1/4" wide x 9-1/4" tall

Lippert Gear Pack - ER- SlideoutEmbeddedRack ("ER") Gear Pack. Specialized gear packused in motorized chassis slide-out systems. Commonly used inTiffin and Monaco systems (140418)

Lippert Standard Gear Pack - Nickel, 15 Teeth

Lippert 2x2 Gear Pack w/o Roll Pins Assy, 15 Teeth

Lippert Motor, In Wall; High Torque, 500:1

Lippert Hydraulic Interior Switch - White

Lippert Hydraulic Interior Switch - Almond

Lippert Reservoir Pump Kit Only, 2 Qt